See Fig. After having placed the turntable mat on the turntable platter. This will disengage the automatic mechanism from the tonearm gear. I Installation of headshell See Fig. Place the balance weight on the rear shaft of the tonearm. Remove the stylus protector, if your cartridge has a detach- able one. Be careful not to touch yourfingers to the stylus tip. See Figs. Excessive forward advancement of the balance weight causes the cartridge side to be lowered. Excessive backward retreatment of the balance weight causes the cartridge side to be raised.
During the adjustment oi the horizontal zero 0 balance, be careful that the stylus tip of the cartridge does not contact the turntable met or turntable base. After the tonearm is horizontally zero 0 balanced. Hold the balance weight stationary with one hand as shown in the picture.
Atter adjusting the horizontal zero 0 balance, turn the balance weight clockwise in the direction 01 the arrow and align to the correct stylus pressuretSee Fig. Set the stylus pressure to the maximum recommended value for your cartridge in cases where the record has an extremely high recording level. Place the dust cover into position from directly above. For detaching the dust cover.
Note: Opening or closing 01 the dust cover during play should be avoided, This may not only cause undesired vibrations. It you must open the dust cover during play. Locate the unit as tar away from the speakers as possible and isolate the unlt from sound radiation trom them. Connect the AC power plug See Fig. Connect the AC power plug to an AC wall socket. Never connect to a DC socket. The AC line-voltage selector is located under the turntable platter. Connect the output terminals See Fig.
Move the toncarm over the desired groove. The turntable platter will start to rotate. Set the cueing lever to the down posttion.
The tonearm will descend slowly onto the record and play will begin. The stylus tip ol the cartridge will be lifted lrom the record. When you play a rpm record with a large center hole. Place the rpm adaptor on the center spindle. The lite oi the stylus differs depending on the conditions ol use. About hours of use is an approximate standard. Align the new stylus assembly with the square opening of the cartridge main body. Installation at cartridge See Fig.
When you install a cartridge. During installation. Connect the lead Wires to the cartridge terminals, The terminals of most cartridges are colour coded. Lettchannels Red Fir. Right channel- 2. Less than 6. Tighten the mounting screws without moving the cartridge. Adjust horizontal zero balance stylus pressure and arm- -litt height whenever you change the cartridge. Even my Mac Mini uses one. You don't need a specific Technics part.
It should be possible to buy a lead pre-packaged with a suitable mains plug on the other end, from any electronics retailer. They are also very often listed on E-bay itself. After being in storage for 8 yrs, I have lost the ground wire for this turn table. Can anyone recommend a replacement part or have a part no.
A friend gave me his SL-Q that he had basically written off. A little TLC and a new stylus and it's good to go! Thanks for posting the manual, it's always good to have around. I think I accidentally broke the needle on my mom's SL-Q and I'm wondering what type of needle you buy to replace it?
I noticed the head of the needle reads "ATLP" and it appears to be yellow, but is there a multitude of needles that could replace it or just one or a few? Is there an audio technica cartridge available for to replace the factory installed one.
I would to know what is compatible with the SL-Q Many thanks But no manual! This is a great service. Thanks very much for hosting this manual. It's simple, but I needed to know to get this old turntable working again. I appreciate the manual for this!. This is a nice little turntable that is simple to setup and operate.
It will make a nice starter table for my niece and having the manual is a real bonus! Hi Looks from the manual page 2, diagram 1 like a standard 2-pin connector, as used for the mains inlet to many portable stereos, some CD players, etc.
0コメント