Youtube tutorial autocad 2007 3d




















This page has been translated for your convenience with an automatic translation service. This is not an official translation and may contain errors and inaccurate translations. Autodesk does not warrant, either expressly or implied, the accuracy, reliability or completeness of the information translated by the machine translation service and will not be liable for damages or losses caused by the trust placed in the translation service.

Back to Topic Listing Previous Next. Filter by Lables. Failure while chamfering. Message 1 of 9. J o i n the extracted top ed g es of the solid into a polyline.

Undo back to the xedges command. Notice tha t right angle of the s w ept t r iangle follows the rectangular path. D e l ete t h e swept solid. Start the Sweep tool and select the re d triangle a s the s w eep object an d the rectangle a s the sweep path.

Change the Visual Style to 3 D wireframe a n d no t ice tha t the rectangular path runs through the midd l e of the tri a ngular pro f ile. If the profile is not perpendicular to the pat h AutoCAD realigns the middle of the profile to the path. Therefore you ma y need to expli c itly loca t e your sweep profile.

Figure 18a. Delete the solid. Repeat selecting different en t ities. Set the UCS back to World. Sweep the r ed circle alon g the line, polyline rectangle, 2 D spline, an d the 3D spline.

Undo an d then sweep along the 3 D spline using the Alignment, No options. D e lete the solid. Sweep the squ a re tube region along the line a s s h ow n. Sweep the r egion along the 3 D spline path this one ma y t a k e a few seconds to complete. Undo the sweep. Sweep the r e gion al o ng t h e rect a ngu l ar polyline pat h. Sweep the b l u e line a s a surface along the line path, rectang u lar polyline, 2D.

Turn off all laye rs except the Loft layer an d make it the active layer. Loft the line to the arc an d the polyline rectangle to the circ l e. Experiment with the Loft Settings. After experimenting undo a n d Loft with t h e Smooth Fit surface control.

Gambar Patung 3 Dimensi Beserta Penjelasannya. Gambar Patung 3 Dimensi Beserta Penjelasannya - Hai sob, dapat berjumpa lagi dengan kami yang selalu setia untuk posting serta berbagi tent Gambar 3 Dimensi Dari Kain Flanel.

Bisa dari video, foto-foto, sampai kumpulan gambar lucu. Biarpun keseruan Gambar Nirmana 3 Dimensi Dari Stik Es Krim - Bukan hal aneh lagi jika media sosial di era sekarang ini telah sering dipakai sebagai alat ko Contoh Gambar 3 Dimensi Binatang. Contoh Gambar 3 Dimensi Binatang - Menghilangkan kejenihan dapat dari apa saja. Misalnya video, kata kata, sampai kumpulan gambar gokil. Gambar Pohon 3 Dimensi.

In the image shown here, what is the offset distance between both the closed geometries? To reduce the size of an object to half of its initial value using SCALE command the scale factor would be?

Fillet will be applied to all Polylines of the drawing. Fillet will be applied to all objects except Polylines. Fillet will be applied to all the vertices of selected Polyline. As per the array command of AutoCAD, what is the row gap between rectangles in this array? To break a Polyline into lines and arcs which command can be used. The command for trim tool is?

As per the array command of AutoCAD, what is the column gap between rectangles in this array? Modifying and manipulating drawing. Part 4 — Drawing tools. What is the name of status bar icon encircled in red?

Ortho mode. Polar tracking. Dynamic input. Object snap tracking. Which option of the status bar will activate the Tooltip as shown on the cursor? Object snap. State True or False: You can change polar tracking angle to any angle of your choice.

To fill closed area with a single color which hatch pattern will you use? Filled area can't be made with hatch command. Which function key enables object snap in AutoCAD? Which factor of hatch command you will change to correct the spacing between hatch lines or pattern?

Which object snap tool was added in AutoCAD version? Geometric center. Apparent intersection. To toggle between different fields of dynamic input which key can be used?

Drawing Tools. Part 5 — Drawing features and properties.



0コメント

  • 1000 / 1000